NAME
pppd
—
Point-to-Point Protocol
daemon
SYNOPSIS
pppd |
[tty_name] [speed] [options] |
DESCRIPTION
PPP is the protocol used for establishing internet links over
dial-up modems, DSL connections, and many other types of point-to-point
links. The pppd
daemon works together with the
kernel ppp(4) driver to
establish and maintain a PPP link with another system (called the
peer) and
to negotiate Internet Protocol (IP) addresses for each end of the link.
pppd
can also authenticate the peer and/or supply
authentication information to the peer. PPP can be used with other network
protocols besides IP, but such use is becoming increasingly rare.
FREQUENTLY USED OPTIONS
- tty_name
- Use the serial port called ttyname to communicate
with the peer. The string “/dev/” is prepended to
ttyname to form the name of the device to open. If
no device name is given, or if the name of the terminal connected to the
standard input is given,
pppd
will use that terminal, and will not fork to put itself in the background. This option is privileged if thenoauth
option is used. - speed
- An option that is a decimal number is taken as the desired baud rate for the serial device. On systems such as 4.4BSD and OpenBSD, any speed can be specified. Other systems (e.g., Linux, SunOS) only support the commonly used baud-rates.
active-filter
filter-expression- Specifies a packet filter to be applied to data packets to determine which
packets are to be regarded as link activity, and therefore reset the idle
timer, or cause the link to be brought up in demand-dialling mode. This
option is useful in conjunction with the
idle
option if there are packets being sent or received regularly over the link (for example, routing information packets) which would otherwise prevent the link from ever appearing to be idle. The filter-expression syntax is as described for tcpdump(8), except that qualifiers which are inappropriate for a PPP link, such as ether and arp, are not permitted. Generally the filter expression should be enclosed in single quotes to prevent whitespace in the expression from being interpreted by the shell. asyncmap
map- This option sets the Async-Control-Character-Map (ACCM) for this end of
the link. The ACCM is a set of 32 bits, one for each of the ASCII control
characters with values from 0 to 31, where a 1 bit indicates that the
corresponding control character should not be used in PPP packets sent to
this system. The map is encoded as a hexadecimal number (without a leading
0x) where the least significant bit (00000001) represents character 0 and
the most significant bit (80000000) represents character 31.
pppd
will ask the peer to send these characters as a 2-byte escape sequence. If multipleasyncmap
options are given, the values are ORed together. If noasyncmap
option is given, no async character map will be negotiated for the receive direction; the peer should then escape all control characters. To escape transmitted characters, use theescape
option. auth
- Require the peer to authenticate itself before allowing network packets to be sent or received.
call
name- Read options from the file /etc/ppp/peers/name.
This file may contain privileged options, such as
noauth
, even ifpppd
is not being run by root. The name string may not begin with "/" or include ".." as a pathname component. The format of the options file is described below. connect
script- Usually there is something which needs to be done to prepare the link
before the PPP protocol can be started; for instance, with a dial-up
modem, commands need to be sent to the modem to dial the appropriate phone
number. This option specifies a command for
pppd
to execute (by passing it to a shell) before attempting to start PPP negotiation. The chat(8) program is often useful here, as it provides a way to send arbitrary strings to a modem and respond to received characters. This option is privileged if thenoauth
option is used. crtscts
- Specifies that
pppd
should set the serial port to use hardware flow control using the RTS and CTS signals in the RS-232 interface. If neither thecrtscts
nor thenocrtscts
option is given, the hardware flow control setting for the serial port is left unchanged. defaultroute
- Add a default route to the system routing tables, using the peer as the
gateway, when IPCP negotiation is successfully completed. This entry is
removed when the PPP connection is broken. This option is privileged if
the
nodefaultroute
option has been specified. disconnect
script- Execute the command specified by script, by passing
it to a shell, after
pppd
has terminated the link. This command could, for example, issue commands to the modem to cause it to hang up if hardware modem control signals were not available. The disconnect script is not run if the modem has already hung up. This option is privileged if thenoauth
option is used. escape
xx,yy,...- Specifies that certain characters should be escaped on transmission
(regardless of whether the peer requests them to be escaped with its async
control character map). The characters to be escaped are specified as a
list of hex numbers separated by commas. Note that almost any character
can be specified for the
escape
option, unlike theasyncmap
option which only allows control characters to be specified. The characters which may not be escaped are those with hex values 0x20 - 0x3f or 0x5e. file
name- Read options from file name (the format is described
below). The file must be readable by the user who has invoked
pppd
. lock
- Specifies that
pppd
should create a UUCP-style lock file for the serial device to ensure exclusive access to the device. mru
n- Set the MRU (Maximum Receive Unit) value to n.
pppd
will ask the peer to send packets of no more than n bytes. The value of n must be between 128 and 16384; the default is 1500. A value of 296 works well on very slow links (40 bytes for TCP/IP header + 256 bytes of data). Note that for the IPv6 protocol, the MRU must be at least 1280. mtu
n- Set the MTU (Maximum Transmit Unit) value to n.
Unless the peer requests a smaller value via MRU negotiation,
pppd
will request that the kernel networking code send data packets of no more than n bytes through the PPP network interface. Note that for the IPv6 protocol, the MTU must be at least 1280. passive
- Enables the "passive" option in the LCP. With this option,
pppd
will attempt to initiate a connection; if no reply is received from the peer,pppd
will then just wait passively for a valid LCP packet from the peer, instead of exiting, as it would without this option.
OPTIONS
- [local_IP_address]:[remote_IP_address]
- Set the local and/or remote interface IP addresses. Either one may be
omitted. The IP addresses can be specified with a host name or in decimal
dot notation (e.g., 150.234.56.78). The default local address is the
(first) IP address of the system (unless the
noipdefault
option is given). The remote address will be obtained from the peer if not specified in any option. Thus, in simple cases, this option is not required. If a local and/or remote IP address is specified with this option,pppd
will not accept a different value from the peer in the IPCP negotiation, unless theipcp-accept-local
and/oripcp-accept-remote
options are given, respectively. bsdcomp
nr,nt- Request that the peer compress packets that it sends, using the
BSD-Compress scheme, with a maximum code size of nr
bits, and agree to compress packets sent to the peer with a maximum code
size of nt bits. If nt is not
specified, it defaults to the value given for nr.
Values in the range 9 to 15 may be used for nr and
nt; larger values give better compression but
consume more kernel memory for compression dictionaries. Alternatively, a
value of 0 for nr or nt
disables compression in the corresponding direction.
nobsdcomp
orbsdcomp 0
disables BSD-Compress compression entirely. chap-interval
n- If this option is given,
pppd
will rechallenge the peer every n seconds. chap-max-challenge
n- Set the maximum number of CHAP challenge transmissions to n (default 10).
chap-restart
n- Set the CHAP restart interval (retransmission timeout for challenges) to n seconds (default 3).
debug
- Enables connection debugging facilities. If this option is given,
pppd
will log the contents of all control packets sent or received in a readable form. The packets are logged through syslogd(8) with facility daemon and level debug. This information can be directed to a file by setting up /etc/syslog.conf appropriately (see syslog.conf(5)). default-asyncmap
- Disable asyncmap negotiation, forcing all control characters to be escaped for both the transmit and the receive direction.
default-mru
- Disable MRU (Maximum Receive Unit) negotiation. With this option,
pppd
will use the default MRU value of 1500 bytes for both the transmit and receive direction. deflate
nr,nt- Request that the peer compress packets that it sends, using the Deflate
scheme, with a maximum window size of 2**nr bytes,
and agree to compress packets sent to the peer with a maximum window size
of 2**nt bytes. If nt is not
specified, it defaults to the value given for nr.
Values in the range 8 to 15 may be used for nr and
nt; larger values give better compression but
consume more kernel memory for compression dictionaries. Alternatively, a
value of 0 for nr or nt
disables compression in the corresponding direction. Use
nodeflate
ordeflate 0
to disable Deflate compression entirely. (Note:pppd
requests Deflate compression in preference to BSD-Compress if the peer can do either.) demand
- Initiate the link only on demand, i.e., when data traffic is present. With
this option, the remote IP address must be specified by the user on the
command line or in an options file.
pppd
will initially configure the interface and enable it for IP traffic without connecting to the peer. When traffic is available,pppd
will connect to the peer and perform negotiation, authentication, etc. When this is completed,pppd
will commence passing data packets (i.e., IP packets) across the link.The
demand
option implies thepersist
option. If this behaviour is not desired, use thenopersist
option after thedemand
option. Theidle
andholdoff
options are also useful in conjunction with thedemand
option. domain
d- Append the domain name d to the local host name for
authentication purposes. For example, if
gethostname(3)
returns the name porsche, but the fully qualified domain name is
porsche.Quotron.COM, you could specify
domain Quotron.COM
.pppd
would then use the name porsche.Quotron.COM for looking up secrets in the secrets file, and as the default name to send to the peer when authenticating itself to the peer. This option is privileged. holdoff
n- Specifies how many seconds to wait before re-initiating the link after it
terminates. This option only has any effect if the
persist
ordemand
option is used. The holdoff period is not applied if the link was terminated because it was idle. idle
n- Specifies that
pppd
should disconnect if the link is idle for n seconds. The link is idle when no data packets (i.e., IP packets) are being sent or received. Note: it is not advisable to use this option with thepersist
option without thedemand
option. If theactive-filter
option is given, data packets which are rejected by the specified activity filter also count as the link being idle. ipcp-accept-local
- With this option,
pppd
will accept the peer's idea of our local IP address, even if the local IP address was specified in an option. ipcp-accept-remote
- With this option,
pppd
will accept the peer's idea of its (remote) IP address, even if the remote IP address was specified in an option. ipcp-max-configure
n- Set the maximum number of IPCP configure-request transmissions to n (default 10).
ipcp-max-failure
n- Set the maximum number of IPCP configure-NAKs returned before starting to send configure-Rejects to n (default 10).
ipcp-max-terminate
n- Set the maximum number of IPCP terminate-request transmissions to n (default 3).
ipcp-restart
n- Set the IPCP restart interval (retransmission timeout) to n seconds (default 3).
ipparam
string- Provides an extra parameter to the ip-up and ip-down scripts. If this option is given, the string supplied is given as the 6th parameter to those scripts.
kdebug
n- Enable debugging code in the kernel-level PPP driver. The argument n is a number which is the sum of the following values: 1 to enable general debug messages, 2 to request that the contents of received packets be printed, and 4 to request that the contents of transmitted packets be printed. On most systems, messages printed by the kernel are logged by syslogd(8) to a file as directed in the /etc/syslog.conf configuration file.
lcp-echo-failure
n- If this option is given,
pppd
will presume the peer to be dead if n LCP echo-requests are sent without receiving a valid LCP echo-reply. If this happens,pppd
will terminate the connection. Use of this option requires a non-zero value for thelcp-echo-interval
parameter. This option can be used to enablepppd
to terminate after the physical connection has been broken (e.g., the modem has hung up) in situations where no hardware modem control lines are available. lcp-echo-interval
n- If this option is given,
pppd
will send an LCP echo-request frame to the peer every n seconds. Normally the peer should respond to the echo-request by sending an echo-reply. This option can be used with thelcp-echo-failure
option to detect that the peer is no longer connected. lcp-max-configure
n- Set the maximum number of LCP configure-request transmissions to n (default 10).
lcp-max-failure
n- Set the maximum number of LCP configure-NAKs returned before starting to send configure-Rejects to n (default 10).
lcp-max-terminate
n- Set the maximum number of LCP terminate-request transmissions to n (default 3).
lcp-restart
n- Set the LCP restart interval (retransmission timeout) to n seconds (default 3).
local
- Don't use the modem control lines. With this option,
pppd
will ignore the state of the CD (Carrier Detect) signal from the modem and will not change the state of the DTR (Data Terminal Ready) signal. login
- Use the system password database for authenticating the peer using PAP, and record the user in the system wtmp file. Note that the peer must have an entry in the /etc/ppp/pap-secrets file as well as the system password database to be allowed access.
maxconnect
n- Terminate the connection when it has been available for network traffic for n seconds (i.e., n seconds after the first network control protocol comes up).
modem
- Use the modem control lines. This option is the default. With this option,
pppd
will wait for the CD (Carrier Detect) signal from the modem to be asserted when opening the serial device (unless a connect script is specified), and it will drop the DTR (Data Terminal Ready) signal briefly when the connection is terminated and before executing the connect script. On Ultrix, this option implies hardware flow control, as for thecrtscts
option. modem_chat
- Use the modem control lines during the chat script. The default is to ignore the state of the CD (Carrier Detect) signal from the modem during the chat script. If you are using a cua(4) device (as opposed to a tty(4) device), you should set this option. You should not use this option with a dialback setup as it will cause the chat script to exit when carrier drops.
ms-dns
[addr]- If
pppd
is acting as a server for Microsoft Windows clients, this option allowspppd
to supply one or two DNS (Domain Name Server) addresses to the clients. The first instance of this option specifies the primary DNS address; the second instance (if given) specifies the secondary DNS address. (This option was present in some older versions ofpppd
under the namedns-addr
.) ms-wins
[addr]- If
pppd
is acting as a server for Microsoft Windows or "Samba" clients, this option allowspppd
to supply one or two WINS (Windows Internet Name Services) server addresses to the clients. The first instance of this option specifies the primary WINS address; the second instance (if given) specifies the secondary WINS address. name
name- Set the name of the local system for authentication purposes to
name. This is a privileged option. With this option,
pppd
will use lines in the secrets files which have name as the second field when looking for a secret to use in authenticating the peer. In addition, unless overridden with theuser
option, name will be used as the name to send to the peer when authenticating the local system to the peer. (Note thatpppd
does not append the domain name to name.) netmask
n- Set the interface netmask to n, a 32-bit netmask in
“decimal dot” notation (e.g. 255.255.255.0). If this option
is given, the value specified is ORed with the default netmask. The
default netmask is chosen based on the negotiated remote IP address; it is
the appropriate network mask for the class of the remote IP address, ORed
with the netmasks for any non point-to-point network interfaces in the
system which are on the same network. (Note: on some platforms,
pppd
will always use 255.255.255.255 for the netmask, if that is the only appropriate value for a point-to-point interface.) noaccomp
- Disable Address/Control compression in both directions (send and receive).
noauth
- Do not require the peer to authenticate itself. This option is privileged
if the
auth
option is specified in /etc/ppp/options. nobsdcomp
- Disables BSD-Compress compression;
pppd
will not request or agree to compress packets using the BSD-Compress scheme. noccp
- Disable CCP (Compression Control Protocol) negotiation. This option should
only be required if the peer is buggy and gets confused by requests from
pppd
for CCP negotiation. nocrtscts
- Disable hardware flow control (i.e., RTS/CTS) on the serial port. If
neither the
crtscts
nor thenocrtscts
option is given, the hardware flow control setting for the serial port is left unchanged. nodefaultroute
- Disable the
defaultroute
option. The system administrator who wishes to prevent users from creating default routes withpppd
can do so by placing this option in the /etc/ppp/options file. nodeflate
- Disables Deflate compression;
pppd
will not request or agree to compress packets using the Deflate scheme. nodetach
- Don't detach from the controlling terminal. Without this option, if a
serial device other than the terminal on the standard input is specified,
pppd
will fork to become a background process. noip
- Disable IPCP negotiation and IP communication. This option should only be
required if the peer is buggy and gets confused by requests from
pppd
for IPCP negotiation. noipdefault
- Disables the default behaviour when no local IP address is specified, which is to determine (if possible) the local IP address from the hostname. With this option, the peer will have to supply the local IP address during IPCP negotiation (unless it was specified explicitly on the command line or in an options file).
nomagic
- Disable magic number negotiation. With this option,
pppd
cannot detect a looped-back line. This option should only be needed if the peer is buggy. nopcomp
- Disable protocol field compression negotiation in both the receive and the transmit direction.
nopersist
- Exit once a connection has been made and terminated. This is the default
unless the
persist
ordemand
option has been specified. nopredictor1
- Do not accept or agree to Predictor-1 compression.
noproxyarp
- Disable the
proxyarp
option. The system administrator who wishes to prevent users from creating proxy ARP entries withpppd
can do so by placing this option in the /etc/ppp/options file. novj
- Disable Van Jacobson style TCP/IP header compression in both the transmit and the receive direction.
novjccomp
- Disable the connection-ID compression option in Van Jacobson style TCP/IP
header compression. With this option,
pppd
will not omit the connection-ID byte from Van Jacobson compressed TCP/IP headers, nor ask the peer to do so. papcrypt
- Indicates that all secrets in the
/etc/ppp/pap-secrets file which are used for
checking the identity of the peer are encrypted, and thus
pppd
should not accept a password which, before encryption, is identical to the secret from the /etc/ppp/pap-secrets file. pap-max-authreq
n- Set the maximum number of PAP authenticate-request transmissions to n (default 10).
pap-restart
n- Set the PAP restart interval (retransmission timeout) to n seconds (default 3).
pap-timeout
n- Set the maximum time that
pppd
will wait for the peer to authenticate itself with PAP to n seconds (0 means no limit). pass-filter
filter-expression- Specifies a packet filter to apply to data packets being sent or received
to determine which packets should be allowed to pass. Packets which are
rejected by the filter are silently discarded. This option can be used to
prevent specific network protocols using up link bandwidth, or to provide
a basic firewall capability. The filter-expression
syntax is as described for tcpdump(8), except that qualifiers which are inappropriate for a
PPP link, such as ether and
arp, are not permitted. Generally the filter
expression should be enclosed in single quotes to prevent whitespace in
the expression from being interpreted by the shell. Note that it is
possible to apply different constraints to incoming and outgoing packets
using the
inbound
andoutbound
qualifiers. persist
- Do not exit after a connection is terminated; instead try to reopen the connection.
predictor1
- Request that the peer compress frames that it sends using Predictor-1 compression, and agree to compress transmitted frames with Predictor-1 if requested. This option has no effect unless the kernel driver supports Predictor-1 compression.
proxyarp
- Add an entry to this system's ARP (Address Resolution Protocol) table with the IP address of the peer and the Ethernet address of this system. This will have the effect of making the peer appear to other systems to be on the local Ethernet.
remotename
name- Set the assumed name of the remote system for authentication purposes to name.
refuse-chap
- With this option,
pppd
will not agree to authenticate itself to the peer using CHAP. refuse-pap
- With this option,
pppd
will not agree to authenticate itself to the peer using PAP. require-chap
- Require the peer to authenticate itself using CHAP (Challenge Handshake Authentication Protocol) authentication.
require-pap
- Require the peer to authenticate itself using PAP (Password Authentication Protocol) authentication.
silent
- With this option,
pppd
will not transmit LCP packets to initiate a connection until a valid LCP packet is received from the peer (as for the `passive' option with ancient versions ofpppd
). usehostname
- Enforce the use of the hostname (with domain name appended, if given) as
the name of the local system for authentication purposes (overrides the
name
option). user
name- Sets the name used for authenticating the local system to the peer to name.
vj-max-slots
n- Sets the number of connection slots to be used by the Van Jacobson TCP/IP header compression and decompression code to n, which must be between 2 and 16, inclusive.
welcome
script- Run the executable or shell command specified by
script before initiating PPP negotiation, after the
connect script (if any) has completed. This option is privileged if the
noauth
option is used. xonxoff
- Use software flow control (i.e., XON/XOFF) to control the flow of data on the serial port.
OPTIONS FILES
Options can be taken from files as well as the command line.
pppd
reads options from the files
/etc/ppp/options, ~/.ppprc
and /etc/ppp/options.ttyname (in that order) before
processing the options on the command line. (In fact, the command-line
options are scanned to find the terminal name before the
options.ttyname file is read.) In forming the name of
the options.ttyname file, the initial /dev/ is removed
from the terminal name, and any remaining / characters are replaced with
dots.
An options file is parsed into a series of words, delimited by
whitespace. Whitespace can be included in a word by enclosing the word in
double-quotes ("). A backslash (\) quotes the following character. A
hash (#) starts a comment, which continues until the end of the line. There
is no restriction on using the file
or
call
options within an options file.
SECURITY
Users must be in group "network" to be able to use
pppd
.
pppd
provides system administrators with
sufficient access control that PPP access to a server machine can be
provided to legitimate users without fear of compromising the security of
the server or the network it's on. In part this is provided by the
/etc/ppp/options file, where the administrator can
place options to restrict the ways in which pppd
can
be used, and in part by the PAP and CHAP secrets files, where the
administrator can restrict the set of IP addresses which individual users
may use.
The normal way that pppd
should be set up
is to have the auth
option in the
/etc/ppp/options file. (This may become the default
in later releases.) If users wish to use pppd
to
dial out to a peer which will refuse to authenticate itself (such as an
internet service provider), the system administrator should create an
options file under /etc/ppp/peers containing the
noauth
option, the name of the serial port to use,
and the connect
option (if required), plus any other
appropriate options. In this way, pppd
can be set up
to allow non-privileged users to make unauthenticated connections only to
trusted peers.
As indicated above, some security-sensitive options are
privileged, which means that they may not be used by an ordinary
non-privileged user running a setuid-root pppd
,
either on the command line, in the user's ~/.ppprc
file, or in an options file read using the file
option. Privileged options may be used in the
/etc/ppp/options file or in an options file read
using the call
option. If
pppd
is being run by the root user, privileged
options can be used without restriction.
AUTHENTICATION
Authentication is the process whereby one peer convinces the other of its identity. This involves the first peer sending its name to the other, together with some kind of secret information which could only come from the genuine authorized user of that name. In such an exchange, we will call the first peer the "client" and the other the "server". The client has a name by which it identifies itself to the server, and the server also has a name by which it identifies itself to the client. Generally the genuine client shares some secret (or password) with the server, and authenticates itself by proving that it knows that secret. Very often, the names used for authentication correspond to the internet hostnames of the peers, but this is not essential.
At present, pppd
supports two
authentication protocols: the Password Authentication Protocol (PAP) and the
Challenge Handshake Authentication Protocol (CHAP). PAP involves the client
sending its name and a cleartext password to the server to authenticate
itself. In contrast, the server initiates the CHAP authentication exchange
by sending a challenge to the client (the challenge packet includes the
server's name). The client must respond with a response which includes its
name plus a hash value derived from the shared secret and the challenge, in
order to prove that it knows the secret.
The PPP protocol, being symmetrical, allows both peers to require the other to authenticate itself. In that case, two separate and independent authentication exchanges will occur. The two exchanges could use different authentication protocols, and in principle, different names could be used in the two exchanges.
The default behaviour of pppd
is to agree
to authenticate if requested, and to not require authentication from the
peer. However, pppd
will not agree to authenticate
itself with a particular protocol if it has no secrets which could be used
to do so.
pppd
stores secrets for use in
authentication in secrets files
(/etc/ppp/pap-secrets for PAP,
/etc/ppp/chap-secrets for CHAP). Both secrets files
have the same format. The secrets files can contain secrets for
pppd
to use in authenticating itself to other
systems, as well as secrets for pppd
to use when
authenticating other systems to itself.
Each line in a secrets file contains one secret. Any following words on the same line are taken to be a list of acceptable IP addresses for that client. If there are only 3 words on the line, or if the first word is "-", then all IP addresses are disallowed. To allow any address, use "*". A word starting with "!" indicates that the specified address is not acceptable. An address may be followed by "/" and a number n, to indicate a whole subnet, i.e., all addresses which have the same value in the most significant n bits. Case is significant in the client and server names and in the secret.
If the secret starts with an `@', what follows is assumed to be
the name of a file from which to read the secret. A "*" as the
client or server name matches any name. When selecting a secret,
pppd
takes the best match, i.e., the match with the
fewest wildcards.
Thus a secrets file contains both secrets for use in
authenticating other hosts, plus secrets which we use for authenticating
ourselves to others. When pppd
is authenticating the
peer (checking the peer's identity), it chooses a secret with the peer's
name in the first field and the name of the local system in the second
field. The name of the local system defaults to the hostname, with the
domain name appended if the domain
option is used.
This default can be overridden with the name
option,
except when the usehostname
option is used.
When pppd
is choosing a secret to use in
authenticating itself to the peer, it first determines what name it is going
to use to identify itself to the peer. This name can be specified by the
user with the user
option. If this option is not
used, the name defaults to the name of the local system, determined as
described in the previous paragraph. Then pppd
looks
for a secret with this name in the first field and the peer's name in the
second field. pppd
will know the name of the peer if
CHAP authentication is being used, because the peer will have sent it in the
challenge packet. However, if PAP is being used,
pppd
will have to determine the peer's name from the
options specified by the user. The user can specify the peer's name directly
with the remotename
option. Otherwise, if the remote
IP address was specified by a name (rather than in numeric form), that name
will be used as the peer's name. Failing that, pppd
will use the null string as the peer's name.
When authenticating the peer with PAP, the supplied password is
first compared with the secret from the secrets file. If the password
doesn't match the secret, the password is encrypted using
crypt(3) and checked against
the secret again. Thus secrets for authenticating the peer can be stored in
encrypted form if desired. If the papcrypt
option is
given, the first (unencrypted) comparison is omitted, for better
security.
Furthermore, if the login
option was
specified, the username and password are also checked against the system
password database. Thus, the system administrator can set up the pap-secrets
file to allow PPP access only to certain users, and to restrict the set of
IP addresses that each user can use. Typically, when using the
login
option, the secret in
/etc/ppp/pap-secrets would be (), which will match
any password supplied by the peer. This avoids the need to have the same
secret in two places.
Authentication must be satisfactorily completed before IPCP (or
any other Network Control Protocol) can be started. If the peer is required
to authenticate itself, and fails to do so, pppd
will terminate the link (by closing LCP). If IPCP negotiates an unacceptable
IP address for the remote host, IPCP will be closed. IP packets can only be
sent or received when IPCP is open.
In some cases it is desirable to allow some hosts which can't
authenticate themselves to connect and use one of a restricted set of IP
addresses, even when the local host generally requires authentication. If
the peer refuses to authenticate itself when requested,
pppd
takes that as equivalent to authenticating with
PAP using the empty string for the username and password. Thus, by adding a
line to the pap-secrets file which specifies the empty string for the client
and password, it is possible to allow restricted access to hosts which
refuse to authenticate themselves.
ROUTING
When IPCP negotiation is completed successfully,
pppd
will inform the kernel of the local and remote
IP addresses for the PPP interface. This is sufficient to create a host
route to the remote end of the link, which will enable the peers to exchange
IP packets. Communication with other machines generally requires further
modification to routing tables and/or ARP (Address Resolution Protocol)
tables. In most cases the defaultroute
and/or
proxyarp
options are sufficient for this, but in
some cases further intervention is required. The
/etc/ppp/ip-up script can be used for this.
Sometimes it is desirable to add a default route through the
remote host, as in the case of a machine whose only connection to the
Internet is through the PPP interface. The
defaultroute
option causes
pppd
to create such a default route when IPCP comes
up, and delete it when the link is terminated.
In some cases it is desirable to use proxy ARP, for example on a
server machine connected to a LAN, in order to allow other hosts to
communicate with the remote host. The proxyarp
option causes pppd
to look for a network interface
on the same subnet as the remote host (an interface supporting broadcast and
ARP, which is up and not a point-to-point or loopback interface). If found,
pppd
creates a permanent, published ARP entry with
the IP address of the remote host and the hardware address of the network
interface found.
When the demand
option is used, the
interface IP addresses have already been set at the point when IPCP comes
up. If pppd
has not been able to negotiate the same
addresses that it used to configure the interface (for example when the peer
is an ISP that uses dynamic IP address assignment),
pppd
has to change the interface IP addresses to the
negotiated addresses. This may disrupt existing connections, and the use of
demand dialling with peers that do dynamic IP address assignment is not
recommended.
SCRIPTS
pppd
invokes scripts at various stages in
its processing which can be used to perform site-specific ancillary
processing. These scripts are usually shell scripts, but could be executable
code files instead. pppd
does not wait for the
scripts to finish. pppd
runs the scripts with
standard input, output and error redirected to
/dev/null, and with an environment that is empty
except for some environment variables that give information about the link.
The environment variables that pppd
sets are:
DEVICE
- The name of the serial tty device being used.
IFNAME
- The name of the network interface being used.
IPLOCAL
- The IP address for the local end of the link. This is only set when IPCP has come up.
IPREMOTE
- The IP address for the remote end of the link. This is only set when IPCP has come up.
PEERNAME
- The authenticated name of the peer. This is only set if the peer authenticates itself.
SPEED
- The baud rate of the tty device.
UID
- The real user ID of the user who invoked
pppd
.
pppd
invokes the following scripts, if
they exist. It is not an error if they don't exist.
- /etc/ppp/auth-up
- A program or script which is executed after the remote system successfully
authenticates itself. It is executed with the parameters
interface-name peer-name user-name tty-device speed
Note that this script is not executed if the peer doesn't authenticate itself, for example when the
noauth
option is used. - /etc/ppp/auth-down
- A program or script which is executed when the link goes down, if /etc/ppp/auth-up was previously executed. It is executed in the same manner with the same parameters as /etc/ppp/auth-up.
- /etc/ppp/ip-up
- A program or script which is executed when the link is available for
sending and receiving IP packets (that is, IPCP has come up). It is
executed with the parameters
interface-name tty-device speed local-IP-address remote-IP-address ipparam
- /etc/ppp/ip-down
- A program or script which is executed when the link is no longer available for sending and receiving IP packets. This script can be used for undoing the effects of the /etc/ppp/ip-up script. It is invoked in the same manner and with the same parameters as the ip-up script.
FILES
- /etc/ppp/pap-secrets
- Usernames, passwords and IP addresses for PAP authentication. This file
should be owned by root and not readable or writable by any other user.
pppd
will log a warning if this is not the case. - /etc/ppp/chap-secrets
- Names, secrets and IP addresses for CHAP authentication. As for
/etc/ppp/pap-secrets, this file should be owned by
root and not readable or writable by any other user.
pppd
will log a warning if this is not the case. - /etc/ppp/options
- System default options for
pppd
, read before user default options or command-line options. - ~/.ppprc
- User default options, read before /etc/ppp/options.ttyname.
- /etc/ppp/options.ttyname
- System default options for the serial port being used, read after ~/.ppprc. In forming the ttyname part of this filename, an initial /dev/ is stripped from the port name (if present), and any slashes in the remaining part are converted to dots.
- /etc/ppp/peers
- A directory containing options files which may contain privileged options,
even if
pppd
was invoked by a user other than root. The system administrator can create options files in this directory to permit non-privileged users to dial out without requiring the peer to authenticate, but only to certain trusted peers.
EXAMPLES
The following examples assume that the
/etc/ppp/options file contains the
auth
option (as in the default
/etc/ppp/options file in the PPP distribution).
Probably the most common use of pppd
is to
dial out to an ISP. This can be done with a command such as
pppd call isp
where the /etc/ppp/peers/isp file is set up by the system administrator to contain something like this:
ttyS0 19200 crtscts connect '/usr/sbin/chat -v -f /etc/ppp/chat-isp' noauth
In this example, we are using chat to dial the ISP's modem and go through any logon sequence required. The /etc/ppp/chat-isp file contains the script used by chat; it could for example contain something like this:
ABORT "NO CARRIER" ABORT "NO DIALTONE" ABORT "ERROR" ABORT "NO ANSWER" ABORT "BUSY" ABORT "Username/Password Incorrect" "" "at" OK "at&d0&c1" OK "atdt2468135" "name:" "^Umyuserid" "word:" "\qmypassword" "ispts" "\q^Uppp" "~-^Uppp-~"
See the chat(8) man page for details of chat scripts.
pppd
can also be used to provide a dial-in
PPP service for users. If the users already have login accounts, the
simplest way to set up the PPP service is to let the users log in to their
accounts and run pppd
(installed setuid-root) with a
command such as
pppd proxyarp
To allow a user to use the PPP facilities, you need to allocate an IP address for that user's machine and create an entry in /etc/ppp/pap-secrets or /etc/ppp/chap-secrets (depending on which authentication method the PPP implementation on the user's machine supports), so that the user's machine can authenticate itself. For example, if Joe has a machine called "joespc" which is to be allowed to dial in to the machine called "server" and use the IP address joespc.my.net, you would add an entry like this to /etc/ppp/pap-secrets or /etc/ppp/chap-secrets:
joespc server "joe's
secret" joespc.my.net
Alternatively, you can create a username called (for example)
"ppp", whose login shell is pppd
and whose
home directory is /etc/ppp. Options to be used when
pppd
is run this way can be put in
/etc/ppp/.ppprc.
If your serial connection is any more complicated than a piece of
wire, you may need to arrange for some control characters to be escaped. In
particular, it is often useful to escape XON (^Q) and XOFF (^S), using
asyncmap a0000
. If the path includes a telnet, you
probably should escape ^] as well (asyncmap
200a0000
). If the path includes an rlogin, you will need to use the
escape ff
option on the end which is running the
rlogin client, since many rlogin implementations are not transparent; they
will remove the sequence (0xff, 0xff, 0x73, 0x73, followed by any 8 bytes)
from the stream.
DIAGNOSTICS
Messages are sent to the syslogd(8) daemon using facility
LOG_DAEMON
. (This can be overridden by recompiling
pppd
with the macro LOG_PPP
defined as the desired facility.) See the syslogd(8) documentation for details of where the syslog
daemon will write the messages. On most systems, the syslog daemon uses the
/etc/syslog.conf file to specify the destination(s)
for syslog messages. You may need to edit that file to suit.
The debug
option causes the contents of
all control packets sent or received to be logged, that is, all LCP, PAP,
CHAP or IPCP packets. This can be useful if the PPP negotiation does not
succeed or if authentication fails. If debugging is enabled at compile time,
the debug
option also causes other debugging
messages to be logged.
Debugging can also be enabled or disabled by sending a SIGUSR1
signal to the pppd
process. This signal acts as a
toggle.
SEE ALSO
cua(4), ppp(4), tty(4), chat(8), syslogd(8), tcpdump(8)
V. Jacobson, Compressing TCP/IP Headers for Low-Speed Serial Links, RFC 1144, February 1990.
R. Rivest, The MD5 Message-Digest Algorithm, RFC 1321, April 1992.
G. McGregor, The PPP Internet Protocol Control Protocol (IPCP), RFC 1332, May 1992.
B. Lloyd and W. Simpson, PPP Authentication Protocols, RFC 1334, October 1992.
W. Simpson, The Point-to-Point Protocol (PPP), RFC 1661, July 1994.
W. Simpson, PPP in HDLC-like Framing, RFC 1662, July 1994.
W. Simpson, PPP Challenge Handshake Authentication Protocol (CHAP), RFC 1994, August 1996.
NOTES
Some limited degree of control can be exercised over a running
pppd
process by sending it a signal from the list
below.
- SIGINT, SIGTERM
- These signals cause
pppd
to terminate the link (by closing LCP), restore the serial device settings, and exit. - SIGHUP
- This signal causes
pppd
to terminate the link, restore the serial device settings, and close the serial device. If thepersist
ordemand
option has been specified,pppd
will try to reopen the serial device and start another connection (after the holdoff period). Otherwisepppd
will exit. If this signal is received during the holdoff period, it causespppd
to end the holdoff period immediately. - SIGUSR1
- This signal toggles the state of the
debug
option. - SIGUSR2
- This signal causes
pppd
to renegotiate compression. This can be useful to re-enable compression after it has been disabled as a result of a fatal decompression error. (Fatal decompression errors generally indicate a bug in one or other implementation.)
AUTHORS
Paul Mackerras <Paul.Mackerras@samba.org>, based on earlier work by Drew Perkins, Brad Clements, Karl Fox, Greg Christy, and Brad Parker.
BUGS
Scripts should be run as root, but are not.